Sandy River Tool Flat

The finished work flat is ready to go. I pretty well cleaned out my O scale detail drawer on this project. When I purchased a Crow River Products clam-shell bucket kit I knew right away were it would go and this project began.

Back over the winter I finished off a Sandy River Car Shop flat. I decided to turn it into a tool car using some of my O scale detail parts including a large bucket. Some up close detail photos were posted some months ago if you scroll back a bit.

This 8 stake pocket flat cars I acquired partly built. I did have to track down O scale stirrups, grabs and trucks. I used HO scale Kadee couplers and pockets. The trucks I eventually used came from a Bachmann flatcar that had its trucks replaced. The Bachmann car got the newer low riding trucks leaving these as excess. The stirrups are Tichy #2009 and Grandt Line 14" brake wheel #33. I used HO scale scale casting for the underside, Walthers 933-829. I later found a O scale piston which was replaced.

A wash of Floquil boxcar red is applied to the sides. The deck has Hunterline weathering mix applied followed by a wash of Floquil grime and Bragdon powders. I did distress the deck before weathering. The lettering is from a Mount Blue Model Co. SR&RL flat car set. Gloss coat and dulcoat was applied using a brush while decaling.

I picked the number from the list of 8 stake flats which ran on the SR&RL. I am not sure if that car ever got the sideboards I added or if it was used as a tool car. I just liked the idea of a flat car loaded with details that could be put to use along the right of way during maintenance....George Dutka

My two Sandy River Car Shops flats I purchased years ago. The top one I have finished and will paint shortly. The bottom flat  is seen as it came to me. A set of Bachmann trucks and a Bachmann On30 flat model are also seen in the photo. Note the Bachmann car is much shorter than the Sandy River car.

Some of the details that will be added to the flat once the sides are built up. The barrels and details mainly came from Schomberg Scale Models. I found a package of joiner bars at a flea market which I also used. Some axes, hammers and lanterns came from Berkshire Valley Models.

The gondola sides are added and given a coat of Hunterline stain. Final weathering will be added shortly along with the decals. The lumber came from mixed Mt. Albert stock. I just used pieces that looked right. From photos I have seen of SR&RL flats these planks could vary.

Some of the details are added. I added a few wooden match sticks stained as bracing and so on. Some other broken scraps of my leftover stripwood is also seen inside the car. The clam-shell was modeled really rusted which I think makes the car. Some concrete blocks by Schomberg Scale Models are added.

Another look with some of the details glued in place.

The work car is loaded with equipment needed down the line. I added some fine wire coils and a couple lengths of chain to the mix.

All the details are glued in place. I did add a bit of real dirt shortly after this photo was taken.

The finished model sits on the Sandy River Car Shops plans.

Wordless Wednesday No. 20

South Strong, Maine

Here is a 1930's view of South Strong. This weeks Wordless Wednesday had a cropped view of the flag stop...note the coach to the rear of the structure. Kind of a neat little scene to model with the curving track and all...George Dutka

Wordless Wednesday No. 19

Schomberg Scale Models - Wood Coal Silo - O Scale

Schomberg Scale Models coal silo applied to a small diorama.

Back in 2010 I picked up and built a Schomberg Scale Models O scale hydrocal wood coal silo with a octagonal roof. A nice looking kit that does take up much room on a layout and pretty basic to build. I guess the hardest part in construction is filling the air bubbles holes found on the main portion of the structure, and that is not all that difficult. The band's turnbuckles need to be glued on. On the roof the cast on ribs I found a bit rough so I replaced them with styrene strips.

The whole structure got a coat of gray primer. The concrete base is Woodland Scenic stone gray. The main body is Floquil boxcar red and tuscan red followed by Bragdon dark rust powders. The roof is painted Floquil Pennsy green with dusting of Bragdon powders. I really like how this model turned out and will be incorporated into my next W&Q module...George Dutka

The band adjusters are separate pieces which are glued on with Canopy glue. The bucket and scoop are from Berkshire Valley.

The base is completed the the main body is primered.

The roof was modeled as weathered copper. Sylvan coal is used around the base.

Lots of weeds are added to the Homasote base. Now days I use Gatorfoam for the base.

A bit of roadway is also applied made of limestone screening.

A Nice Size SR&RL Train to Model

A SR&RL mixed train. Two boxcars, gondola and combine...a great little train size to model for me in O scale.

Peter Mumby passed along this winter scene photo after our trip to Maine...a really nice view of the SR&RL train at Strong, Maine...After seeing in person the replica Strong station and two foot equipment in Portland Peter can better relate to Maine two foot modeling...George Dutka

SR&RL Train Crew

Here we have a typical looking SR&RL crew...guess we should be dressing our scale figures this way.